加工定制：是
一、 适用范围APPLICATION
适用于贮存压缩空气,供舰船主辅机的起动及鸣放汽笛之用,也可作为气动设备的气源.
THIS COMPRESSED AIR RECEIVER WHICH COMPLIES THE STANDARD CB/T493-93,CAN BE USED FOR STARING SHIPS MAIN ENGINES AND AUXILIARY ENGINES, ALSO TO SUPPLY POWER TO DRIVE WHISTLE AND PNEUMATIC EQUIPMENTS.
二、 结构形式见下图TYPE AND COMSTRUCTION AS BELOW
1.瓶头阀BOTTLE HEAD VALVE 2.铭牌NAME PLATE
3.本体BODY 4.排污螺塞DRAINAGE SCREW BOLT
FIG . (1) VERTICAL TYPE
FIG. (2) HORIZonTAL TYPE
1.本体BODY 2.进气阀INLET VALVE 3.压力表PRE.GAURE
4.铭牌NAME PLATE 5.安全阀SAFETY VALVE 6.遥控阀TELEConTROL VALVE 7.出气阀OUTLET VALVE 8.排污阀DRAINAGE VALVE 9.人孔装置MANHOLE DEVICE
三、安装INSTALLTION
1.A型空气瓶用抱箍安装,其尺寸根据空气瓶直径制作,A型空气瓶的抱箍与筒体之间,B型空气瓶支座需用3-5mm的橡胶式铅板作衬垫,以防剧烈震动.
A FITTING RING SHOULD BE USED TO A-TYPE AIR RECEIVER ACCORD TO IT’S DIAMETER, RUBBER OR LEAD BELT3-5 IN THICKNESS TO BE FILLING BETWEEN THE FITTING RING AND BODY OR THE SUPPORT AND FOUNDTION (B TYPE) TO PREVENT SHOCK.
2.安装空气瓶所用的管材壁应清洁,以防杂屑进入瓶内,如停留阀体内降低密封性能
TUBES ConNECTED WITH AIR RECEIVER SHOULD BE COMPLETELY CLEAN BEFORE FITTED OTHERWISE SOMETHING MAY GET IN AND DAMAGE THE SEAL OF VALVES.
3.仪表继电器需用¢6紫铜管,从对应的阀口接出,安装在醒目的仓壁上.
INSTRUMENT AND RELAY TO BE ConNECTED WITH￠6 COPPER TUBES FROM CORRESPonDING VALVES AND FITTEDIN EYE-CATCHING WALL.
四、 及保养MAINTENANCE
阀杆四周漏气,压紧螺帽松,填料太少,拧紧压紧螺帽,增厚填料重新拧紧螺帽.LEAKAGE AROUND THE VALVE ROD￡NOT ENOUGH FITTING OR NUT LOOSEI￡REPAIR ADDING FILLING AND TIGHT NUT
阀漏气其原因：阀腔有杂物，阀体磨损密封破坏，处理方法：拆开阀清洗杂物，原样装复，用研磨砂研磨（氧化铝80目，180目），先粗后细，更换。VALVE SEAL LEAKAGE：SEAL DAMAGED REPAIR，DISMANTLE THE VALVE SEAL 8L？CLEAN THE SYSTEM POLISH THE SEAL SURFACE（WITH 80HOLE/INCH 180HOLE/INCH）REFITTING。
人孔瓶头阀座板间漏气：其原因为螺帽松动，密封垫圈损坏，处理方法：拧紧螺帽更换垫圈。MANHOLE HEAD VALVE LEAKAGE：WASHER DAMAGE OR NUTS LOOSE REPAIR：RENEW WASHER AND TIGHT NUTS。
定时排水排污DRAIN THE BILGE REULARLY五、 随机文件documentS ATTACHED
总图GENERAL DRAWING产品质量证明书PRODUCT QUALITY GUARANTEE船检证书SHIPING SOCIETY CERTIFICATE质量返溃单USER SHEET—PRODUCT QUALITY MESSAGE装箱单LIST OF GOODS使用说明书INSTRUCTION BOOK六、 贮存STORAGE
空气瓶应放在干燥室内贮存。
THE AIR RECEIVER SHOULD BE IN DRY ROOM。
证书文件:
